Herder kitchen knife kettle fuller grind
Knife handles made of steamed, finely polished wood are rare. Knife handles made of steamed, finely polished apple tree wood are even rarer because apple tree wood, since it dries slowly, is not one of the typical commercial woods. However, it is very easy to work with due to its hardness, weight and durability. Herder in Solingen manufactures these knife handles with rarity value exclusively for Manufactum: even oiled for better surface protection.
The blade runs from the back of the knife first in a "crowned" rounding and then goes into a really thinly ground cutting edge. The shape and grind of the blade make this knife a fine all-purpose tool for cutting and carving vegetables, meat and fish.
Solingen Thin Grind: nail-flush and scrape clean.
Windmühlen knives from Robert Herder in Solingen are remarkable not only for the knife steel (at least 0.75% carbon content and a hardness of at least 56 HRC for the carbon steels), but above all for the craftsman's finishing, which spares none of the traditional grinding efforts: Windmühlen knives are ground extremely thin. This results in their amazing cutting ability, which is an experience in use. The most elaborate type of grinding is the whale grind, a special type of thin grinding in which the blade is ground tapered towards the back of the knife.
Pließten is the name given in Solingen to the smoothing of the grinding grooves remaining on the blade, i.e. the fine grinding. The most complex stage of this technique is blue finishing. In this process, the steel is ground finer step by step. That a blade is blugepließtet, you can tell by the fact that it reflects in the light slightly bluish.
Longer sharp thanks to higher hardness.
The elastic blades of the blue-plated knives from Herder are ground in the Solingen thin grinding as well as in the whale grinding. Thanks to the very high hardness of 60 Rockwell (HRC) they keep their sharpness much longer.
Because of the high hardness - and because they are ground so exceedingly thin - the blades should not be turned or even canted, as this may lead to chipping on the material when cutting.
Not stainless, but really sharp.
The traditional material for knife blades is carbon steel. This is not stainless, but with a fine-grained structure it can be hardened to a particularly high degree and made extremely sharp. The higher the carbon content, the higher the hardening capacity. These knives owe their high cutting ability to the material in addition to the finishing, and their high cutting edge retention to a material-related self-sharpening effect. Each time a cut is made through fruit or vegetables, a minimal amount of material is removed and the blade wears evenly. The knifemaker refers to this as micro-corrosion. In fact, this means that the blade becomes steadily narrower over the years - but always retains its sharp grinding angle. Blades made of carbon steel put on a dark patina over time, but this in no way negatively affects their quality, but on the contrary gives them better protection against corrosion.
Carbon steel knives do not belong in the dishwasher. Wipe the knives dry after rinsing and occasionally apply some blade oil. Discoloration may occur on the blade material. However, this is not a sign of inferior quality, but only indicates the rather high carbon content in the material. In case of flash rust, the use of the rust eraser is recommended. A resharpening can be done with the sharpening steel.
Article Number 41246
Carbon steel knifes are not suitable for use in dishwashers. Wipe the knife dry after washing (if it has not been used for a longer period of time, apply a little blade oil). For films of rust use of a rust eraser is recommended. Re-sharpen with a sharpening steel.
With apple wood half handles. Blade length 15 cm, total length 26.5 cm. Weight 85 g.
Because of their high degree of hardness, the blades should never be twisted or turned. Under certain circumstances this can lead to ruptures in the material.
If you have a question concerning this product you are welcome to contact us. For this your E-Mail program will open.
For advice, spare parts or special requests - our customer centre will take care of your questions and concerns, personally and competently.
You can reach us from Monday to Friday at +49 2309 939095 or anytime at firstname.lastname@example.org
Exclusive at Manufactum
Several particularly noteworthy products from selected manufacturers are available from us in a distinct form. In any case, these special editions offer you a maximum of quality in material and functionality.Find exclusive products